In this article below you can locate a bunch of really good material on the subject of Installing A Bathtub.
Installing a tub isn't specifically rocket science, yet it does need strong plumbing, woodworking, and also often, tiling skills. Replacing an old bath tub with a brand-new one is additionally a moderately challenging project. If the old bathtub is easily obtainable, the task can relocate immediately; if you need to open up a wall surface to eliminate the old tub and place the brand-new bathtub, the job is much harder. In either instance, the job is within a house handyman's skills, although you will certainly require an assistant to vacate the old bathtub and also embeded in the brand-new one. See to it you have qualified on your own for the work as well as are comfortable attempting it. As opposed to employing a service provider to take over a halfway-completed task, it is far better to think about employing one prior to you start. Possibilities are you may require a specialist plumber to make tube connections.
This article will certainly aid you install a new bath tub in your washroom if you have actually currently purchased a new bathtub and also don't require to transform the arrangement of your previous supply of water pipes.
Your devices as well as material list should comprise the following:
Removing Old Touches
If you need to change old faucets with brand-new ones as a part of your installation, after that the first thing you should do is separate the supply of water. After doing so, turn on the faucets to drain pipes any type of water continuing to be in the system. The procedure of removing the existing faucets can be quite troublesome as a result of the restricted access that is typically the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the taps. Have a towel all set for the continuing to be water that will certainly come from the pipes. When the supply pipes have been eliminated, make use of the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from turning during this process. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleaned of any kind of old sealing compound.
Prior to going on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Fitting New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin ensuring that the washers remain in place between the tap and also the sink. Secure the tap in place with the producer supplied backnut. As soon as the tap is safely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal tap connectors. The former kind needs to be connected to the tap finishes initially, tightening up just by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Setting up the Bathtub
Making use of the two wooden boards under its feet, place the bath tub in the needed placement. The wooden boards are useful in equally spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four tiny points.
The next goal is to make certain that the tub is leveled all round. This can be attained by inspecting the spirit level and also adjusting the feet on the bathtub until the spirit level checks out level.
To mount taps, fit all-time low of the furthest adaptable faucet connector to the appropriate supply pipeline by making a compression sign up with; then do the same for the other tap.
Switch on the supply of water and examine all joints and also new pipework for leakages as well as tighten them if needed. Load the bath tub and likewise check the overflow outlet and the regular outlet for leakages.
Ultimately, repair the bath paneling as described in the maker's user's manual. Tiling and also sealing around the tub must wait up until the bathtub has actually been made use of at least when as this will settle it into its last placement.
Getting ready for the Setup
Firstly, the sustaining framework supplied with the bath should be fitted (if required) according to the supplier's directions. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is very important to make sure that if the tap comes with a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is also practical to fit a supporting plate under the taps device to prevent stress on the bathtub.
Fit the flexible tap connectors to the bottom of the two faucets using 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you use all of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom must now be ready to be fitted in its last setting.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to split a rigid seal, causing the water to pass through the wall in between the bathroom and also the tiling, bring about complications with wetness and possible leakages to the ceiling below.
You can select from a range of coloured sealers to assimilate your components and fittings. They are sold in tubes and cartridges, and are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with twists of drenched paper or soft rope. Remember to always fill up the bath tub with water prior to securing, to allow for the motion experienced when the tub is in usage. The sealer can fracture rather early if you do not take into consideration this motion prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently offered on the market. It is recommended to fit the tiles using water-resistant or waterproof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a passionate person who reads on Installing A Bathtub, I thought sharing that piece of content was worthwhile. For those who enjoyed reading our article if you please remember to pass it around. Thank you for your time spent reading it.
Need assistance? Call.